Search results

  1. Question Bluetooth trace 10 reads short to ground

    Okay so I have spotted something that looks like it might be signal but the problem is that the sginal is around 10mV so I suspect it might just be noise
  2. Question Bluetooth trace 10 reads short to ground

    Twisting them together did not help, I still can't sync my wiimotes on the rvloader menu.
  3. Question Bluetooth trace 10 reads short to ground

    I've tried to measure the traces with the oscilloscope but both of them are always low, is this normal? Trying to twist them a little more right now, they were actually as twisted as my USB wires.
  4. Question Bluetooth trace 10 reads short to ground

    So I cut the trace on a different point and now the short is gone, but the relocation still doesn't work. @CrazyGadget here is the picture of the board where I cut and soldered the wires.
  5. Question Bluetooth trace 10 reads short to ground

    Hey all, I'm trying to figure out why my bluetooth relocation suddenly decided not to work, without the module connected, the trace which should be connected to pin 10 reads short to ground. I've tried to cut the trace before it arrives at the edge of the board but that didn't fix it. Visibly...
  6. Worklog My first wii portable

    Currently designing a case for the handheld, am wondering if i could fit 3 18650 batteries like so. i am going to lift the wii motherboard a centimeter and put stuff (regulators, power management) there and hope they dont create noise to interfere with the wii.
  7. RVLoader v2.1

    this was the culprit, I made the 1v15 and 1v lines thicker, along with the ground wires and it works now
  8. RVLoader v2.1

    the usb female connectors were cut off from the wii motherboard, and i made sure there were no shorts between the layers. am measuring 4.7v between power and ground, twisted a pair of wire for data and currently getting the dsi exception after a long loading screen when booted up
  9. RVLoader v2.1

    i tried an another usb drive and it still doesn't work - can this be because of my wiring?
  10. RVLoader v2.1

    I tried with two usb sd card readers with three sd cards. should i be using a usb flash drive instead?
  11. RVLoader v2.1

    How long should the loading screen last for? It has been 2 minutes and it is still loading. Does this mean a bad usb drive? Sometimes it also spits out a core dump Here is the dump i was talking about, sometimes it is stuck on the loading screen, other times I get this.
  12. Question No video coming from composite

    Thanks for the reply, I am using a 2 amp regulator from a powerbank, that thing connected to the fan is a 12 volt regulator for the fan to spin if you are talking about that one. But my question is, this was working perfectly fine until i rewired the regulators. Would replacing the cables fix that?
  13. Question No video coming from composite

    It was working and I decided to clean up my regulator wiring. Now I have no signal. All the voltages are there, there is also 1v8 and 3v3 on the ave rvl chip, but there is no signal. checked with an oscilloscope and saw nothing.
  14. Worklog My first wii portable

    i don't know how, but i forgot that usb was supposed to be a twisted pair - twisting the data cables worked and now everything is fully functional again
  15. Question Usb doesn't work

    twisted the cables, now it works i guess
  16. Question Usb doesn't work

    Usb stopped working after desoldering and resoldering the wires, tried CM1 and CM2. even tried soldering from different points as shown in the trimming guide. i can see a signal like this on the scope: ____________________________ | | _| but RVloader says it cannot initialize fat fs.
  17. Worklog My first wii portable

    added a parallel 10k resistor to the 3v3 regulator's 2k2, now at least bluetooth works
  18. Worklog My first wii portable

    I designed and printed a case for this portable today, but i broke something i guess. usb and bluetooth no longer works.
  19. Worklog My first wii portable

    ive decided to use an old usb sd card reader as my storage device, so i disassembled that and soldered it in place. it now boots into rvloader and works with a wiimote.
Top