What's new

5 Inch Eyoyo Component Screen

Joined
Dec 30, 2021
Messages
59
Likes
11
H and V sync are for VGA, you would connect to the VGA connector, or follow the traces back and connect to where they go. You'll also need R, G, and B if you want to get a video signal out of it too :P
can i use this vga scheme on any board that has this same chip model?RTD2660H?

can i use this vga scheme on any board that has this same chip model?RTD2660H?
I'm wondering how to install component video on ps2 portable on controller board
 

Luke

.
.
Joined
May 23, 2016
Messages
219
Likes
247
Location
Texas
Portables
2
can i use this vga scheme on any board that has this same chip model?RTD2660H?

I'm wondering how to install component video on ps2 portable on controller board
This particular board apparently has a quirk in that the RGB pins are out of order, and what Cheese posted is the typical pinout.

If you had this exact board, Stitches picture is the one to follow.

But if as you say you have another driver that happens to use the same chip, it doesn't stand to reason that the driver would *necessarily* have the same mistake - I would default to using the correct pinout unless I knew otherwise.

Side note, you seem to be using the terms VGA and Component interchangeably and they're not quite the same, as Cheese noted, VGA uses H and V sync in addition to RGB.

Hope this helps!
 

Stitches

2 and a Half Dollarydoos
Staff member
.
.
Joined
Feb 5, 2017
Messages
4,181
Likes
3,278
Location
Banana Bender Land, Australia
Portables
6
can i use this vga scheme on any board that has this same chip model?RTD2660H?


I'm wondering how to install component video on ps2 portable on controller board
This particular board apparently has a quirk in that the RGB pins are out of order, and what Cheese posted is the typical pinout.

If you had this exact board, Stitches picture is the one to follow.

But if as you say you have another driver that happens to use the same chip, it doesn't stand to reason that the driver would *necessarily* have the same mistake - I would default to using the correct pinout unless I knew otherwise.

Side note, you seem to be using the terms VGA and Component interchangeably and they're not quite the same, as Cheese noted, VGA uses H and V sync in addition to RGB.

Hope this helps!
Just to confirm, VGA input uses the "correct" typical pinout as shown in any VGA diagram out there. It's just the component input mode that they for some reason set the pins out of order
 
Joined
Dec 30, 2021
Messages
59
Likes
11
Esta placa em particular aparentemente tem uma peculiaridade em que os pinos RGB estão fora de ordem, e o que Cheese postou é a pinagem típica.

Se você tivesse essa prancha exata, a imagem de Stitches é a que segue.

Mas se, como você diz, você tem outro driver que usa o mesmo chip, não é lógico que o driver *necessariamente* tenha o mesmo erro - eu usaria como padrão a pinagem correta, a menos que soubesse o contrário.

Nota lateral, você parece estar usando os termos VGA e Component de forma intercambiável e eles não são exatamente os mesmos, como Cheese observou, VGA usa sincronização H e V além de RGB.

Espero que isto ajude!
[/CITAR]
This particular board apparently has a quirk in that the RGB pins are out of order, and what Cheese posted is the typical pinout.

If you had this exact board, Stitches picture is the one to follow.

But if as you say you have another driver that happens to use the same chip, it doesn't stand to reason that the driver would *necessarily* have the same mistake - I would default to using the correct pinout unless I knew otherwise.

Side note, you seem to be using the terms VGA and Component interchangeably and they're not quite the same, as Cheese noted, VGA uses H and V sync in addition to RGB.

Hope this helps!
thank you very much, I understand only this board has a different connection, so I can use the typical pinout on other boards that have VGA with a chip model RTD2660H
 

Stitches

2 and a Half Dollarydoos
Staff member
.
.
Joined
Feb 5, 2017
Messages
4,181
Likes
3,278
Location
Banana Bender Land, Australia
Portables
6
thank you very much, I understand only this board has a different connection, so I can use the typical pinout on other boards that have VGA with a chip model RTD2660H
Chip model is irrelevent. If it has a soldered in VGA port, the pinout is always the same. If the board uses JST connectors, the pinout will be marked in the silkscreen on the underside of the board
 
Joined
Dec 30, 2021
Messages
59
Likes
11
Chip model is irrelevent. If it has a soldered in VGA port, the pinout is always the same. If the board uses JST connectors, the pinout will be marked in the silkscreen on the underside of the board
Thank you friend
 
Joined
Dec 30, 2021
Messages
59
Likes
11
Chip model is irrelevent. If it has a soldered in VGA port, the pinout is always the same. If the board uses JST connectors, the pinout will be marked in the silkscreen on the underside of the board
friend sorry to bother, but why did you circle that part in red and white?
I circled in green showing
 

Attachments

Stitches

2 and a Half Dollarydoos
Staff member
.
.
Joined
Feb 5, 2017
Messages
4,181
Likes
3,278
Location
Banana Bender Land, Australia
Portables
6
friend sorry to bother, but why did you circle that part in red and white?
I circled in green showing
Those are the right and left audio in points. Right is red and left is white, like standard RCA inputs
 
Joined
Dec 30, 2021
Messages
59
Likes
11
Those are the right and left audio in points. Right is red and left is white, like standard RCA inputs
I see, have you ever made a portable console? do you have a project post done? Would like to see
 
Joined
May 31, 2020
Messages
8
Likes
4
necrobump!! I hope someone can dump this firmware and we can use it to build more yPbPr screens!
 

Stitches

2 and a Half Dollarydoos
Staff member
.
.
Joined
Feb 5, 2017
Messages
4,181
Likes
3,278
Location
Banana Bender Land, Australia
Portables
6
necrobump!! I hope someone can dump this firmware and we can use it to build more yPbPr screens!
If that was ever done, it wouldn't be shared here. Much like sharing ROMs, sharing RTD firmware dumps is illegal
 

Y2K

"The PS1 Guy"
Staff member
.
.
Joined
Apr 14, 2022
Messages
181
Likes
400
Location
Chicago, IL
necrobump!! I hope someone can dump this firmware and we can use it to build more yPbPr screens!
Necroposting is generally frowned upon on forums, there probably wasn't any reason to bring this thread back after a month of inactivity.

Anyways, only really legal way to do this is to do a clean room reverse engineering effort, which would involve dumping the firmware, reverse engineering it to understand how it works, and reimplementing it from scratch. The original firmware binaries should not be shared around because it would be copyright infringement to do so.
 
Top